Factory specifications, fluid capacities, torque values, EPA fuel economy and the federal safety record for the 2008 335I xDrive.
The 2008 BMW 335I xDrive. It takes 6.9 qt of 15W-40 engine oil and is EPA-rated at 17/26/20 mpg city/highway/combined.
Fluid capacities, tune-up values and fuel economy at a glance.
Replacement part sizes and factory part numbers — battery, bulbs, filters and belts.
From the factory this vehicle uses a BCI 48 · 570 CCA battery, OE oil filter 11428683168. Each part links to every other vehicle that shares it, so a part you already stock may fit more of your fleet than you'd expect.
| Engine oil filter | 11428683168 alt 11428637821 |
| Engine air filter | 13717556961 |
| Fuel filter | 16147163296 |
| Spark plug | 12120037244 |
| Front wiper blades | 61612468942 alt 61612468941 |
| Thermostat | 11537549476 |
| Cabin air filter | 64319142114 alt 64319313519 |
Engine, drivetrain, dimensions and economy.
| Transmission | Automatic (S6) |
| Overall length | 178.3 in |
| Overall width | 71.7 in |
| Overall height | 55.9 in |
| Wheelbase | 108.7 in |
| Curb weight | 3594 lb |
| Track (front / rear) | 59.1 / 59.4 in |
| Weight distribution (front / rear) | 50/50 |
| EPA city / highway / combined | 17 / 26 / 20 mpg |
| Drivetrain | Rear-Wheel Drive |
| Passenger volume | 93 cu ft |
| Cargo volume | 12 cu ft |
| Recommended fuel | Premium Gasoline |
Capacities, torques and tune-up values from the factory service manual.
This engine holds 6.9 qt of 15W-40 / 10W-40 / 10W-30 API SJ engine oil, DOT 4 brake fluid. Torque lug nuts to 88 ft-lbs, the oil drain plug to M12 Bolts: 18.0, M22 Bolts: 44.0 ft-lbs. The firing order is 1-5-3-6-2-4. Note the cylinder-head bolts finish on a torque angle (torque-to-yield) — they stretch permanently and should be replaced, not reused, during any head service.
| Brake Fluid | DOT 4 |
| Differential Gear Oil Capacity | 2.3 Pints |
| Engine Coolant | ETHYLENE GLYCOL |
| Engine Oil | 15W-40 · API · 10W-40 · 10W-30 · 5W-30 |
| Engine Oil Capacity | 6.9 qt |
| Manual Transmission Fluid | BMW MTF part number 83220309031 |
| Manual Transmission Fluid Capacity | 3.2 |
| Power Steering Fluid | Use Pentosin CHF 11S |
| Engine Flywheel Bolts | AT: 92 ft-lbs, MT: 89 ft-lbs |
| Intake Manifold to Engine Bolts | 11 ft-lbs |
| Exhaust Manifold to Cylinder Head Bolts | 15 ft-lbs |
| Engine Oil Pan Drain Plug | M12 Bolts: 18.0, M22 Bolts: 44.0 ft-lbs |
| Lug Nuts | 88 ft-lbs |
| Cylinder Firing Order | 1-5-3-6-2-4 |
| Spark Plug Manufacturer | BMW |
| Refrigerant | R134a |
| Refrigerant Capacity | 1.19-1.40 lbs |
| Oil Group | PAG |
| Oil Type | 46 |
| Oil Capacity | 5.70-6.50 oz |
| Optional BCI Group Number | 94R |
| Optional BCI Cranking Performance | 640 cca |
| Standard BCI Group Number | 48 |
| Engine Compression | 130-261 PSI. 29 maximum variation. psi |
| Minimum Pad Thickness | Front: 0.145; Rear: 0.145 pads |
| Rotor Nominal Thickness From | 0.394 in |
| Rotor Nominal Thickness To | 0.394 in |
| Rotor Discard at or Under | 0.331 in |
| 1 | 15 ft. lbs., Step 2: 137 | 15 ft. lbs |
Prep Do not reuse old bolts
| 1 | 22.0 ft. lbs. | 22 ft. lbs |
| 2 | 90 degrees | 90 degrees |
| 3 | Bolts 1-10 90 degrees | 90 degrees |
| 4 | 45 degrees | 45 degrees |
| 1 | 15 ft. lbs., Step 2: 70 | 15 ft. lbs |
The most common OBD-II codes for this vehicle's emissions system. These are standardized SAE J2012 definitions, not vehicle-specific fault reports.
Decode factory build data for a specific vehicle by VIN.
Find every vehicle that shares this one's battery, bulbs, oil capacity, platform or parts.
Cross-vehicle references for the kinds of data on this page.
6.9 qt of HIGH PERFORMANCE MINERAL OILS: ABOVE 5 degrees F: 15W-40 API SJ, SL OR SM, -5 degreesF TO 68 degrees F: 10W-40 API SJ, SL OR SM, 5 degreesF TO 50 degrees F: 10W-30 API SJ, SL OR SM, BELOW 50 degrees F: 5W-30 API SJ, SL OR SM, BELOW 32 degrees F:, per the factory manual.
EPA figures are 17 city / 26 highway / 20 combined mpg.