Factory specifications, fluid capacities, torque values, EPA fuel economy and the federal safety record for the 2012 RVR.
Replacement part sizes and factory part numbers — battery, bulbs, filters and belts.
From the factory this vehicle uses a BCI 35 · 520 CCA battery. Each part links to every other vehicle that shares it, so a part you already stock may fit more of your fleet than you'd expect.
Engine, drivetrain, dimensions and economy.
| Overall length | 169.3 in |
| Overall width | 69.7 in |
| Overall height | 64.2 in |
| Wheelbase | 105.1 in |
| Curb weight | 3031 lb |
| Track (front / rear) | 60.2 / 60.2 in |
| Weight distribution (front / rear) | 59/41 |
Capacities, torques and tune-up values from the factory service manual.
The firing order is 1-3-4-2. Note the cylinder-head bolts finish on a torque angle (torque-to-yield) — they stretch permanently and should be replaced, not reused, during any head service.
| Power Steering Fluid | Genuine Mitsubishi PS fluid |
| Power Steering Fluid | Use Mitsubishi PS fluid |
| Camshaft Bearing/Carrier Cap Bolts or Studs | 8 |
| Crankshaft Pulley and/or Damper Bolts | 184 Turbo ft-lbs |
| Engine Flywheel Bolts | 98 ft-lbs |
| Oil Pump to Cylinder BLock Bolts/Studs | 13 ft-lbs |
| Cylinder Firing Order | 1-3-4-2 |
| Curb Idle Speed (No Load) | 700 Turbo rpm |
| Curb Idle Speed Variance (No Load) | 100 rpm |
| Standard BCI Group Number | 35 |
| Standard BCI Cranking Performance | 520 cca |
| Regulated Fuel System Pressure (Without Vacuum) | 45.0-50.0 psi |
| Engine Compression | 152 |
| Torque Caliper to Bracket | 28-36 ft-lbs / 24-28 ft-lbs |
| Torque to Knuckle | 67-81 ft-lbs / 38-48 ft-lbs |
| Rotor Max Parallel Variation | 0.0006 in |
| Rotor Runout Limit | 0.0024 in / 0.0032 in |
| Rotor Nominal Thickness From | 1.024 in / 0.394 in |
| Rotor Nominal Thickness To | 1.024 in / 0.394 in |
| Rotor Discard at or Under | 0.96 in / 0.33 in |
| 1 | 15 ft. lbs., Step 2: 90-100 | 15 ft. lbs |
| 1 | 26 ft. lbs. | 26 ft. lbs |
| 2 | 90 degrees. | 90 degrees |
| 3 | 90 degrees.; Do not re-use old bolts. Apply an appropriate amount of engine oil to top and bottom surfaces of washers and threaded portion of bolts. | 90 degrees |
| 1 | 25-27 ft. lbs. | 25–27 ft. lbs |
| 2 | 90 degrees | 90 degrees |
| 3 | 90 degrees; Do not re-use old bolts. Apply an appropriate amount of engine oil to top and bottom surface of washers and threaded portion of bolts. | 90 degrees |
The most common OBD-II codes for this vehicle's emissions system. These are standardized SAE J2012 definitions, not vehicle-specific fault reports.
Decode factory build data for a specific vehicle by VIN.
Find every vehicle that shares this one's battery, bulbs, oil capacity, platform or parts.
Cross-vehicle references for the kinds of data on this page.