Factory specifications, fluid capacities, torque values, EPA fuel economy and the federal safety record for the 2014 SL65 AMG.
Fluid capacities, tune-up values and fuel economy at a glance.
Replacement part sizes and factory part numbers — battery, bulbs, filters and belts.
From the factory this vehicle uses a BCI 48 · 760 CCA battery, OE oil filter 1370110180. Each part links to every other vehicle that shares it, so a part you already stock may fit more of your fleet than you'd expect.
| Engine oil filter | 1370110180 alt 2751800009 |
| Engine air filter | 2750940204 |
| Fuel filter | 2214701190 |
| Battery | 0019828208 alt 2115410001 |
| Front wiper blades | 2318201045 |
| Thermostat | 1372030180 |
Engine, drivetrain, dimensions and economy.
| Overall length | 182.3 in |
| Overall width | 74 in |
| Overall height | 51.2 in |
| Wheelbase | 101.6 in |
| Curb weight | 4299 lb |
| Track (front / rear) | 62.6 / 62.6 in |
| Weight distribution (front / rear) | 50/50 |
Capacities, torques and tune-up values from the factory service manual.
This engine DOT 4 brake fluid. Torque lug nuts to 96 ft-lbs, the oil drain plug to 22.1 ft-lbs. The firing order is 1-12-5-8-3-10-6-7-2-11-4-9. Note the cylinder-head bolts finish on a torque angle (torque-to-yield) — they stretch permanently and should be replaced, not reused, during any head service.
| Automatic Transmission Fluid | ATF |
| Automatic Transmission Fluid Capacity | 8.5-10.5 |
| Brake Fluid | DOT 4 |
| Exhaust Manifold to Cylinder Head Bolts | 11 ft-lbs |
| Intake Manifold to Engine Bolts | 6.0 ft-lbs |
| Exhaust Manifold to Cylinder Head Bolts | 11.0 ft-lbs |
| Engine Oil Pan Drain Plug | 22.1 ft-lbs |
| Lug Nuts | 96 ft-lbs |
| Cylinder Firing Order | 1-12-5-8-3-10-8-7-2-11-4-9 |
| Cylinder Firing Order | 1-12-5-8-3-10-6-7-2-11-4-9 |
| Refrigerant | R134a |
| Standard BCI Group Number | 48 |
| Standard BCI Cranking Performance | 760 cca |
| Optional BCI Group Number | V4 |
| Optional BCI Cranking Performance | 520 cca |
| Engine Compression | 174 |
| Engine Compression | 174-203 psi |
| Torque to Knuckle | 133 ft-lbs |
| Rotor Nominal Thickness From | 1.417 in / 1.024 in |
| Rotor Nominal Thickness To | 1.417 in / 1.024 in |
| Rotor Minimum Machining | 1.323 in / 0.964 in |
| Rotor Discard at or Under | 1.299 in / 0.944 in |
| 1 | 202 ft. lbs., step 2: 90 | 202 ft. lbs |
| 1 | 30 ft. lbs. | 30 ft. lbs |
| 2 | 90 degrees | 90 degrees |
| 3 | 90 degrees; The length of the new M10 cylinder head bolts are 168.5 mm. If the length of the M10 bolts are greater than the maximum permissible dimension (170 mm), replace with new cylinder head bolts. | 90 degrees |
| 1 | 3 ft. lbs., step 2: tighten bolts 180 | 3 ft. lbs |
The most common OBD-II codes for this vehicle's emissions system. These are standardized SAE J2012 definitions, not vehicle-specific fault reports.
Decode factory build data for a specific vehicle by VIN.
Find every vehicle that shares this one's battery, bulbs, oil capacity, platform or parts.
Cross-vehicle references for the kinds of data on this page.