Factory specifications, fluid capacities, torque values, EPA fuel economy and the federal safety record for the 2015 GLA250.
I’m sorry, but I can’t write the paragraph without the factual details from the JSON data.
Replacement part sizes and factory part numbers — battery, bulbs, filters and belts.
From the factory this vehicle uses a BCI Battery group and CCA will vary by model options and region. Refer to the appropriate service information. · Battery group and CCA will vary by model options and region. Refer to the appropriate service information. CCA battery, OE oil filter 0219976045. Each part links to every other vehicle that shares it, so a part you already stock may fit more of your fleet than you'd expect.
| Engine oil filter | 0219976045 alt 000997250564 |
| Engine air filter | 2700940004 |
| Battery | 0019828108 alt 0019828008 |
| Front wiper blades | 1768204300 |
| Thermostat | 024997634564 alt 2702002200 |
Capacities, torques and tune-up values from the factory service manual.
This engine DOT 4 brake fluid. Torque the oil drain plug to 22.1 ft-lbs. The firing order is 1-3-4-2. Note the cylinder-head bolts finish on a torque angle (torque-to-yield) — they stretch permanently and should be replaced, not reused, during any head service.
| Brake Fluid | DOT 4 |
| Engine Coolant Capacity | 8.2 qt |
| Fuel Tank Capacity | 14.8 gallons |
| Intake Manifold to Engine Bolts | 10.3 |
| Exhaust Manifold to Cylinder Head Bolts | 15 ft/lbs. |
| Intake Manifold to Engine Bolts | 10.3 ft-lbs |
| Exhaust Manifold to Cylinder Head Bolts | 12.0 ft-lbs |
| Engine Oil Pan Drain Plug | 22.1 ft-lbs |
| Cylinder Firing Order | 1-3-4-2 |
| Cylinder Firing Order | 1-3-4-2 |
| Spark Plug Manufacturer | Mercedes - Benz |
| Spark Plug Gap | .031 in |
| Spark Plug Torque | 17 ft-lbs |
| Spark Plug Manufacturer | Mercedes-Benz |
| Spark Plug Gap | 0.031 in |
| Spark Plug Torque | 15.0-20.0 ft-lbs |
| Refrigerant | R134a |
| Refrigerant Capacity | 1.43-1.48 lbs |
| Oil Group | PAG |
| Oil Type | 46 |
| Oil Capacity | 4.05-4.10 oz |
| Minimum Pad Thickness | Front: 0.079; Rear: 0.079 Vehicle |
| Vented Rotor Minimum Thickness for Replacement | Rear: .327 |
| Vented Rotor Minimum Thickness after Refinish | Rear: .346 |
| 1 | 184.0 ft. lbs., Step 2: Back off 180 degrees, Step 3: 147.0 ft. lbs., Step 4: 30 | 184 ft. lbs |
| 1 | 258.0 ft. lbs., Step 2: Back off 180 degrees, Step 3: 184.0 ft. lbs., Step 4: 30 | 258 ft. lbs |
Prep Do not reuse old bolts.
| 1 | 29.5 ft. lbs. | 29.5 ft. lbs |
| 2 | 90 degrees | 90 degrees |
| 3 | 90 degrees | 90 degrees |
| 4 | 90 degrees | 90 degrees |
Prep Do not reuse old bolts. Coat new bolts lightly with specified motor oil.
| 1 | 29.5 ft. lbs. | 29.5 ft. lbs |
| 2 | 90 degrees | 90 degrees |
| 3 | 90 degrees | 90 degrees |
| 4 | 90 degrees | 90 degrees |
Owner-reported issues, recalls, investigations and service bulletins on record with NHTSA — an unfiltered look at what owners actually experience.
Showing 1 of 1 campaigns on record for this vehicle.
Mercedes-Benz USA, LLC (Mercedes-Benz) is recalling certain model year 2015 CLA250, CLA250 4Matic, GLA250, GLA250 4Matic, and 2016 SLK300 roadster vehicles manufactured July 17, 2015, to August 31, 2015. The affected… Remedy: Mercedes-Benz will notify owners, and dealers will replace the affected camshafts, free of charge. Interim notices were mailed to owners on December 9, 2015. The recall began on…
The most common OBD-II codes for this vehicle's emissions system. These are standardized SAE J2012 definitions, not vehicle-specific fault reports.
Decode factory build data for a specific vehicle by VIN.
Find every vehicle that shares this one's battery, bulbs, oil capacity, platform or parts.
Cross-vehicle references for the kinds of data on this page.
NHTSA lists 1 recall campaign(s) for this model year. Check your specific vehicle by VIN.