Factory specifications, fluid capacities, torque values, EPA fuel economy and the federal safety record for the 2016 E63 AMG S.
Replacement part sizes and factory part numbers — battery, bulbs, filters and belts.
From the factory this vehicle uses a BCI Battery group and CCA will vary by model options and region. Refer to the appropriate service information. · Battery group and CCA will vary by model options and region. Refer to the appropriate service information. CCA battery, OE oil filter 0309970748. Each part links to every other vehicle that shares it, so a part you already stock may fit more of your fleet than you'd expect.
| Engine oil filter | 0309970748 alt 2781840280 |
| Spark plug | 0041598103 |
| Battery | 0019828108 alt 000982960864 |
| Front wiper blades | 2128201700 |
| Thermostat | 2782010280 alt 2782001700 |
Capacities, torques and tune-up values from the factory service manual.
This engine 75W-85 · 75W-83 in the differential, DOT 4 brake fluid. Torque the oil drain plug to 22.1 ft-lbs. The firing order is 1-5-4-2-6-3-7-8. Note the cylinder-head bolts finish on a torque angle (torque-to-yield) — they stretch permanently and should be replaced, not reused, during any head service.
| Brake Fluid | DOT 4 |
| Differential Gear Oil | 75W-85 · 75W-83 |
| Differential Gear Oil Capacity | 2.0-4.0 |
| Engine Coolant Capacity | 11.5 qt |
| Intake Manifold to Engine Bolts | 6.6 |
| Intake Manifold to Engine Bolts | 6.6 ft-lbs |
| Exhaust Manifold to Cylinder Head Bolts | M7 nuts: 11.0, M8 nuts: 16.0 ft-lbs |
| Engine Oil Pan Drain Plug | 22.1 ft-lbs |
| Cylinder Firing Order | 1-5-4-2-6-3-7-8 |
| Cylinder Firing Order | 1-5-4-2-6-3-7-8 |
| Spark Plug Manufacturer | Mercedes-Benz |
| Spark Plug Gap | 0.031 in |
| Spark Plug Torque | 15.0-20.0 ft-lbs |
| Refrigerant | R134a |
| Oil Group | PAG |
| Oil Type | 46 |
| Oil Capacity | 4.06 oz |
| Brake Caliper Bolt to Carrier Torque | Front: 96; Rear: 18 |
| Brake Caliper Carrier to Hub Bolt Torque | Front: 85; Rear: 85 /; Rear: 85 |
| Minimum Pad Thickness | Front: 0.079; Rear: 0.079 Vehicle |
| Vented Rotor Minimum Thickness after Refinish | Front: w/out Code B07: 1.318; All others NS |
| 1 | 118.0 ft. lbs., Step 2: Back off 360 degrees, Step 3: 88.0 ft. lbs., Step 4: 90 | 118 ft. lbs |
Prep Do not reuse old bolts. Coat new bolts lightly with specified motor oil. · Bolts 1-10
| 1 | 14.8 ft. lbs. | 14.8 ft. lbs |
| 2 | 29.5 ft. lbs. | 29.5 ft. lbs |
| 3 | 90 degrees | 90 degrees |
| 4 | 90 degrees | 90 degrees |
| 5 | 90 degrees | 90 degrees |
| 6 | Bolt 11 10.3 ft. lbs. | 10.3 ft. lbs |
The most common OBD-II codes for this vehicle's emissions system. These are standardized SAE J2012 definitions, not vehicle-specific fault reports.
Decode factory build data for a specific vehicle by VIN.
Find every vehicle that shares this one's battery, bulbs, oil capacity, platform or parts.
Cross-vehicle references for the kinds of data on this page.