Factory specifications, fluid capacities, torque values, EPA fuel economy and the federal safety record for the 2004 CLK55 AMG Cabriolet.
Fluid capacities, tune-up values and fuel economy at a glance.
Replacement part sizes and factory part numbers — battery, bulbs, filters and belts.
From the factory this vehicle uses a BCI 49 · 760 CCA battery, OE oil filter 0259976448. Each part links to every other vehicle that shares it, so a part you already stock may fit more of your fleet than you'd expect.
| Engine oil filter | 0259976448 alt 0259976548 |
| Battery | 0009823308 alt 0009823108 |
| Thermostat | 1122030076 alt 1122030275 |
| Cabin air filter | 2038301200 |
Engine, drivetrain, dimensions and economy.
| Overall length | 182.7 in |
| Overall width | 68.5 in |
| Overall height | 54.3 in |
| Wheelbase | 107.1 in |
| Curb weight | 3902 lb |
| Track (front / rear) | 58.3 / 57.1 in |
| Weight distribution (front / rear) | 53/47 |
Capacities, torques and tune-up values from the factory service manual.
This engine DOT 4 brake fluid. Torque lug nuts to 96 ft-lbs, the oil drain plug to 22.1 ft-lbs. The firing order is 1-5-4-2-6-3-7-8.
| Automatic Transmission Fluid | ATF |
| Automatic Transmission Fluid Capacity | 7.5-9.5 |
| Brake Fluid | DOT 4 |
| Differential Gear Oil Capacity | 3.4 Pints |
| Engine Coolant | USE ONLY COOLANT MEETING MB SHEET 325.0 |
| Intake Manifold to Engine Bolts | 15 ft-lbs |
| Exhaust Manifold to Cylinder Head Bolts | 12 ft-lbs |
| Engine Oil Pan Drain Plug | 22.1 ft-lbs |
| Lug Nuts | 96 ft-lbs |
| Cylinder Firing Order | 1-5-4-2-6-3-7-8 |
| Spark Plug Gap | 0.031 in |
| Refrigerant | R134a |
| Refrigerant Capacity | 1.87 lbs |
| Oil Group | PAG |
| Oil Type | MB part number 0019890803 or equivalent |
| Standard BCI Group Number | 49 |
| Standard BCI Cranking Performance | 760 cca |
| Regulated Fuel System Pressure (Without Vacuum) | 54.0-61.0 psi |
| Regulated Fuel System Pressure (With Vacuum) | 46.0-52.0 psi |
| Engine Compression | 159-189 psi |
| Torque Caliper to Bracket | 41 ft-lbs |
| Torque to Knuckle | 81 ft-lbs / 85 ft-lbs |
| Minimum Pad Thickness | Front: 0.079; Rear: 0.079 in |
| Rotor Nominal Thickness From | 0.866 in / 1.181 in |
| Rotor Nominal Thickness To | 0.866 in / 1.181 in |
| Rotor Minimum Machining | 0.787 in / 1.102 in |
| Rotor Discard at or Under | 0.768 in / 1.083 in |
The most common OBD-II codes for this vehicle's emissions system. These are standardized SAE J2012 definitions, not vehicle-specific fault reports.
Decode factory build data for a specific vehicle by VIN.
Find every vehicle that shares this one's battery, bulbs, oil capacity, platform or parts.
Cross-vehicle references for the kinds of data on this page.