Factory specifications, fluid capacities, torque values, EPA fuel economy and the federal safety record for the 2013 CL65 AMG.
The 2013 Mercedes CL65 AMG takes 9.5 qt of 0W-30 engine oil.
Fluid capacities, tune-up values and fuel economy at a glance.
Replacement part sizes and factory part numbers — battery, bulbs, filters and belts.
From the factory this vehicle uses a BCI 49 · 850 CCA battery, OE oil filter 2751800009. Each part links to every other vehicle that shares it, so a part you already stock may fit more of your fleet than you'd expect.
| Engine oil filter | 2751800009 |
| Engine air filter | 2750940204 |
| Battery | 0019828208 |
| Front wiper blades | 2218201300 |
| Thermostat | 1372030180 |
| Cabin air filter | 2218300718 |
Capacities, torques and tune-up values from the factory service manual.
This engine holds 9.5 qt of 0W-30 / 5W-30 / 0W-40 engine oil, DOT 4 brake fluid. Torque lug nuts to 110 ft-lbs, the oil drain plug to 22.1 ft-lbs. The firing order is 1-12-5-8-3-10-6-7-2-11-4-9. Note the cylinder-head bolts finish on a torque angle (torque-to-yield) — they stretch permanently and should be replaced, not reused, during any head service.
| Automatic Transmission Fluid | ATF |
| Automatic Transmission Fluid Capacity | 8.5-10.5 |
| Brake Fluid | DOT 4 |
| Differential Gear Oil Capacity | 3 Pints |
| Engine Oil | 0W-30 · 5W-30 · 0W-40 · 5W-40 · 5W-50 |
| Engine Oil Capacity | 9.5 qt |
| Intake Manifold to Engine Bolts | 6 ft-lbs |
| Exhaust Manifold to Cylinder Head Bolts | 11 ft-lbs |
| Intake Manifold to Engine Bolts | 6.0 ft-lbs |
| Exhaust Manifold to Cylinder Head Bolts | 11.0 ft-lbs |
| Engine Oil Pan Drain Plug | 22.1 ft-lbs |
| Lug Nuts | 110 ft-lbs |
| Cylinder Firing Order | 1-12-5-8-3-10-8-7-2-11-4-9 |
| Cylinder Firing Order | 1-12-5-8-3-10-6-7-2-11-4-9 |
| Refrigerant | R134a |
| Refrigerant Capacity | 2.40 lbs |
| Oil Group | PAG |
| Oil Type | 46 |
| Oil Capacity | 3.72 oz |
| Standard BCI Group Number | 49 |
| Standard BCI Cranking Performance | 850 cca |
| Optional BCI Group Number | V4 |
| Engine Compression | 174 |
| Engine Compression | 174-203 psi |
| Torque Caliper to Bracket | 81 ft-lbs / 21 ft-lbs |
| Torque to Knuckle | 110 ft-lbs / 133 ft-lbs |
| Rotor Nominal Thickness From | 1.023 in / 1.417 in |
| Rotor Nominal Thickness To | 1.023 in / 1.417 in |
| Rotor Minimum Machining | 0.944 in / 1.338 in |
| Rotor Discard at or Under | 0.921 in / 1.315 in |
| 1 | 202 ft. lbs., step 2: 90 | 202 ft. lbs |
| 1 | 30 ft. lbs. | 30 ft. lbs |
| 2 | 90 degrees | 90 degrees |
| 3 | 90 degrees; The length of the new cylinder head bolts are 132mm. If the length of the bolts are greater than the maximum permissible dimension (135.5mm), replace with new cylinder head bolts. | 90 degrees |
The most common OBD-II codes for this vehicle's emissions system. These are standardized SAE J2012 definitions, not vehicle-specific fault reports.
Decode factory build data for a specific vehicle by VIN.
Find every vehicle that shares this one's battery, bulbs, oil capacity, platform or parts.
Cross-vehicle references for the kinds of data on this page.
9.5 qt of 0W-30, 5W-30, 0W-40, 5W-40 OR 5W-50, per the factory manual.