JeepGrand Wagoneer2022Overview/jeep/grand-wagoneer/2022/base/

2022 Jeep Grand Wagoneer

Factory specifications, fluid capacities, torque values, EPA fuel economy and the federal safety record for the 2022 Grand Wagoneer.

The 2022 Jeep Grand Wagoneer, whose powertrain maintenance calls for 7.0 quarts of 0W-40 engine oil, sits at an awkward peak in the nameplate's long reliability record. Tracking owner complaints from 1990 through 2026, the 2022 model year registers the highest total at 55—a sharp contrast to the single complaint recorded in 1991—while also carrying 9 recalls, with electrical system issues leading the reported problems. For researchers, this combination makes the 2022 Grand Wagoneer a clear outlier in the model's history, an inflection point where dependability data diverges sharply from the broader nameplate trend.

Model year202520242023202219931991199019891988

Quick specs

Fluid capacities, tune-up values and fuel economy at a glance.

Engine oil capacity7.0 qtOEM · verified
Engine oil type0W-40OEM · verified
Lug nut torque130.0 ft-lbsOEM · verified

Fitment & sizes

Replacement part sizes and factory part numbers — battery, bulbs, filters and belts.

From the factory this vehicle uses OE oil filter 68466307AB. Each part links to every other vehicle that shares it, so a part you already stock may fit more of your fleet than you'd expect.

Tire size285/45R22/XL 114HOEM · verified
Wheel / rim9.0 inOEM · verified

OE service part numbers OEM · verified

Engine oil filter68466307AB alt 04892339BE
Engine air filter68575644AB
Spark plugSP149212AC alt 68265438AB
Battery68715228AA alt 56029642AB
Front wiper blades68490448AA
Thermostat52028898AJ alt 68361650AH
Cabin air filter68548579AA

Full specifications

Engine, drivetrain, dimensions and economy.

Dimensions & weight NHTSA vPIC

Overall length214.6 in
Overall width83.5 in
Overall height75.6 in
Wheelbase122.8 in
Curb weight6340 lb
Track (front / rear)68.5 / 68.5 in
Weight distribution (front / rear)51/49

Performance & power Independent road tests

0–60 mph, quarter-mile, horsepower and torque from independent road tests.

Independent road tests for the Grand Wagoneer of this era, listed by trim and engine — this page spans more than one engine, so no single horsepower figure is shown.

5.4–5.7 sec0–60 mph (tested)quickest 5.40 sec — 2022 Obsidian
YearTrim / engine0–60¼ mileHPDrivetrain
2022Obsidian 6.4L V85.40 sec13.90 sec471 hp4WD
2022Series II 6.4L V85.40 sec13.90 sec471 hp4WD
2022Series II 6.4L V85.70 sec14.10 sec471 hp4WD
2022Series III 6.4L V85.70 sec14.10 sec471 hp4WD
2023L Series III 3.0L Twin-Turbo I-64.70 sec13.50 sec510 hp4WD
2023L Series II 3.0L Twin-Turbo I-64.90 sec13.50 sec510 hp4WD
2023L Series II 3.0L Twin-Turbo I-65.00 sec13.50 sec510 hp4WD
2025Series III Obsidian 3.0L Twin-Turbo I-64.60 sec13.10 sec510 hp4WD

Service quick specs OEM factory data

Capacities, torques and tune-up values from the factory service manual.

This engine holds 7.0 qt of 0W-40 engine oil, 75W-85 · GL-5 · Synthetic in the differential, DOT 3 brake fluid. Torque lug nuts to 130.0 ft-lbs, the oil drain plug to 25.0 ft-lbs. The firing order is 1-8-4-3-6-5-7-2.

Lubricants & capacities

Automatic Transmission FluidATF
Automatic Transmission Fluid Capacity8.98 qt
Brake FluidDOT 3
Differential Gear Oil75W-85 · GL-5 · Synthetic
Engine Coolant Capacity18.8 qt
Engine OilSynthetic · 0W-40 · MS-12633
Engine Oil Capacity7.0 qt
Transfer Case FluidBW48-30: Mopar Mobile LT

Engine torques

Crankshaft Position (CKP) Sensor Bolt(s)9.0 ft-lbs
Camshaft Position (CMP) Sensor Bolt(s)9.0 ft-lbs
Oxygen (O2S) Sensor Bolt(s)37.0 ft-lbs
Knock Sense (KS) Bolt(s)15.0 ft-lbs
Intake Manifold to Engine Bolts9.0 ft-lbs
Engine Oil Pan Drain Plug25.0 ft-lbs
Oil Pump to Cylinder BLock Bolts/Studs10.3 ft-lbs

Chassis torques

Differential Fill Plug26.0 ft-lbs
Differential drain Plug26.0 ft-lbs
Lug Nuts130.0 ft-lbs
Transfer Case Fill PlugBW48-30: 18.0 ft-lbs; BW48-12: 15.0 ft-lbs
Transfer Case Drain PlugBW48-30: 18.0 ft-lbs; BW48-12: 15.0 ft-lbs
Automatic Transmission Drain PlugDrain: 6.6 ft-lbs; Fill: 26.0 ft-lbs

Ignition

Cylinder Firing Order1-8-4-3-6-5-7-2
Spark Plug ManufacturerMopar
Spark Plug Gap0.043" in
Spark Plug Torque11.0 ft-lbs

Battery & A/C

RefrigerantR1234yf
Refrigerant Capacity2.125 lbs
Oil TypeND-Oil 12
Oil Capacity7.80 oz

Service checks

Injector Primary Resistance11.4-12.6 @ 68 degreesF ohms

Brakes

Brake Caliper Bolt to Carrier TorqueFront: 55.0 ft-lbs; Rear: 26.0 ft-lbs
Brake Caliper Carrier to Hub Bolt TorqueRear: 96.0 ft-lbs
ABS Sensor Torque6.6
Minimum Pad Thickness0.040" in
Solid Rotor Minimum Thickness for ReplacementFront: 1.118; Rear: 0.858
Variation from Parallelism Thickness Variation0.0006"
Maximum Rotor Runout0.0008"

Multi-step torque procedures OEM · verified

Inspection Procedure (Upper) — tightening sequence 1 stages
1Place jack stands as far out as possible under both lower control arms. Step 3: The vehicle can now be lowered onto the jack stands supporting as much weight as possible. Step 4: Remove front tires. Step 5: Place plunger on upper side of upper ball joint making sure that it is perpendicular to boss machined surface. Step 6: Use a pry bar between upper control arm and knuckle to pry upward. Step 7: Document movement from the dial indicator. Step 8: Replace upper control arm and ball joint if travel exceeds specifications.
Inspection Procedure (Lower) — tightening sequence 1 stages
1Place jack stands as far out as possible under both lower control arms. Step 3: The vehicle can now be lowered onto the jack stands supporting as much weight as possible. Step 4: Remove front tires. Step 5: Place plunger on upper side of upper ball joint making sure that it is perpendicular to boss machined surface. Step 6: Use a pry bar between upper control arm and knuckle to pry upward. Step 7: Document movement from the dial indicator. Step 8: Replace upper control arm and ball joint if travel exceeds specifications.
Engine Flywheel Bolts — tightening sequence 1 stages
137 ft. lbs., Step 2: 92 ft. lbs., Step 3: 3037 ft. lbs
Main Bearings — tightening sequence 6 stages
1Using new bolts, install the twenty six M12 bolts (1 - 26) and the three M8 bolts finger tight.
2Using the tightening shown, tighten all M12 bolts to 33 ft. lbs.33 ft. lbs
3Using a torque angle gauge, tight the internal bed plate bolts (1 - 16) an additional 110 degrees.110 degrees
4Tight the external bed plate bolts 89 ft. lbs.89 ft. lbs
5Tighten the three M8 bolts 22 ft. lbs.22 ft. lbs
6Check the torque of the M12 bolts in a counterclockwise direction with the torque wrench set at 85

Factory maintenance schedule OEM · verified

Normal service, condensed from the factory interval matrix.

Under the factory schedule, replace the spark plugs every 90,000 mi; coolant at 150,000 mi. The big-interval services (at 150,000 mi for coolant, and the transmission fluid) are the ones owners most often skip — on a lower-mileage example, assume the original fluids are still in it and check them first.

Every 10,000 miBattery (inspect) · Brake Line (inspect) · Brake Linings (inspect) · Brake Rotor (inspect) · CV Joint Boot (inspect) · Engine Coolant System (inspect fluid level)
Every 12,000 miCabin Air Filter (replace)
Every 20,000 miDifferential (inspect fluid level) · Suspension System (inspect) · Tie Rod (inspect)
Every 30,000 miEngine Air Filter Element (replace)
Every 90,000 miSpark Plugs (replace)
Every 100,000 miPCV Valve (replace)
At 150,000 miDrive Belt (replace) · Drive Belt Tensioner (inspect) · Engine Coolant System (drain, flush & refill) · Transfer Case Assembly (drain & refill)

Owner how-tos

Condensed service procedures for routine maintenance. Procedures that require dealer diagnostic equipment are identified and summarized only.

Common procedures

Key fob — remote (RKE) programming programming new fob buttons Dealer tool OEM · verified
Tool requiredDRBIII scan tool (dealer / locksmith)
WhyTransmitter codes are written into the receiver in the passenger door module
Anti-theft (SKIS) — module initialization after immobilizer module replacement Dealer tool OEM · verified
When neededAfter Sentry Key Immobilizer Module (SKIM) replacement
Tool requiredDRBIII scan tool
Also requiredThe vehicle's four-digit PIN code

Reliability & federal safety record

Owner-reported issues, recalls, investigations and service bulletins on record with NHTSA — an unfiltered look at what owners actually experience.

The provided federal record shows a clear discontinuity between the 1990s data and the modern era, with 2022 marking the start of a new production cycle that exhibits the highest regulatory activity in the available data. Specifically, the 2022 model year records 55 complaints and 9 recalls, which are the peak figures before declining to 44 complaints and 7 recalls in 2023 and further to 33 complaints in 2024. Technical Service Bulletins are also most prevalent in 2022 with 915 entries, substantially exceeding the 533 recorded for the following year, while top complaint areas include the Electrical System, Seats, Engine, and Visibility/Wiper alongside one crash and one fire complaint. This downward trend in complaints and recalls across subsequent years implies that the 2022 model carries the highest concentration of initial production issues within this data set. Therefore, this is a higher-risk choice than later model years and requires confirmation that all 9 recalls and 915 TSBs have been completed before purchase.

9
Open recalls
NHTSA campaigns
915
Service bulletins
Manufacturer communications
0
ODI investigations
Office of Defects Investigation
55
Owner complaints
1 involved a crash · 1 a fire
NHTSA crash-test rating federal NCAP · out of 5 stars
Overall★★★★★
Frontal★★★★★
Side★★★★★
Rollover★★★★
Owner complaints by model year NHTSA · this generation & adjacent

Owner complaints filed with NHTSA, by component

All 55 complaints on record, top 8 components.

Electrical System5
Seats3
Engine3
Visibility/Wiper3
Structure2
Suspension,Power Train,Electrical System2
Steering,Electrical System,Fuel/Propulsion System2
Electrical System,Engine2

Source: NHTSA Office of Defects Investigation complaint database.

Recalls NHTSA · verified

Showing 2 of 9 campaigns on record for this vehicle.

21V919000SeatsReported 23/11/2021

Chrysler (FCA US, LLC) is recalling certain 2022 Jeep Wagoneer and Grand Wagoneer vehicles. The second-row center-seat recliner pull strap may bind on the seat trim surface, preventing the seat back from locking into… Remedy: Dealers will inspect and replace as necessary, the rear center-seat recliner strap, free of charge. Owner notification letters were mailed December 23, 2021. Owners may contact…

21V873000Air Bags: Air Bag/Restraint Control Module:SoftwareReported 10/11/2021

Chrysler (FCA US, LLC) is recalling certain 2021 Jeep Grand Cherokee L, 2022 Jeep Wagoneer, and Grand Wagoneer vehicles. The Occupant Restraint Controller (ORC) may have incorrect software which can disable the driver… Remedy: Dealers will reprogram the ORC, free of charge. Owner notification letters were mailed December 2, 2021. Owners may contact FCA US, LLC customer service at 1-800-853-1403. FCA US…

Technical service bulletins NHTSA · verified

Showing 5 of 915 bulletins on record with NHTSA.

BulletinDateComponentSummary
1131232026-06-29Service BrakesSPRING KIT - DISC BRAKE PAD
S2508000025 REV.A2026-06-26Electrical SystemInstrument Panel Cluster (IPC) and Radio Compass Display has Dashes (--)
1129802026-06-22Electrical SystemCAMERA - REAR VIEW
1129792026-06-22Electrical SystemCAMERA - REAR VIEW
91008332026-06-17Fuel/Propulsion SystemFuel Delivery Module Before replacing the fuel module for DTCs P0461 and P062A and other…

Common OBD-II trouble codes

The most common OBD-II codes for this vehicle's emissions system. These are standardized SAE J2012 definitions, not vehicle-specific fault reports.

P0420
Catalyst system efficiency below threshold — Bank 1
P0300
Random / multiple cylinder misfire detected
P0171
System too lean — Bank 1
P0455
Evaporative emission system leak detected — large leak
P0128
Coolant thermostat below regulating temperature
P0442
Evaporative emission system leak detected — small leak

VIN tools

Decode factory build data for a specific vehicle by VIN.

VIN
Decode a VIN to confirm the transmission and build data for a specific Grand Wagoneer. OEM
Build data
Plant, GVWR class, engine and body data for any 17-character VIN.
Recalls
Check open recall campaigns against a specific vehicle by VIN.

Vehicles with shared specs

Find every vehicle that shares this one's battery, bulbs, oil capacity, platform or parts.

Reference guides

Cross-vehicle references for the kinds of data on this page.

Frequently asked

How much oil does the 2022 Grand Wagoneer take?

7.0 qt of Mopar Full Synthetic 0W-40 meeting MS-12633., per the factory manual.

Does the 2022 Grand Wagoneer have open recalls?

NHTSA lists 9 recall campaign(s) for this model year. Check your specific vehicle by VIN.