2018 Jaguar XJR575

Factory specifications, fluid capacities, torque values, EPA fuel economy and the federal safety record for the 2018 XJR575.

Quick specs

Fluid capacities, tune-up values and fuel economy at a glance.

Lug nut torque92 ft-lbsOEM · verified

Fitment & sizes

Replacement part sizes and factory part numbers — battery, bulbs, filters and belts.

From the factory this vehicle uses OE oil filter AJ812279. Each part links to every other vehicle that shares it, so a part you already stock may fit more of your fleet than you'd expect.

OE service part numbers OEM · verified

Engine oil filter	AJ812279 alt AJ811453
Engine air filter	C2Z15037
Spark plug	C2P23089
Battery	429123482
Front wiper blades	C2D60832
Cabin air filter	C2Z6525

Service quick specs OEM factory data

Capacities, torques and tune-up values from the factory service manual.

Torque lug nuts to 92 ft-lbs, the oil drain plug to 18.0 ft-lbs. The firing order is 1-5-4-2-6-3-7-8. Note the cylinder-head bolts finish on a torque angle (torque-to-yield) — they stretch permanently and should be replaced, not reused, during any head service.

Engine torques

Crankshaft Position (CKP) Sensor Bolt(s)	7.4 ft-lbs
Camshaft Position (CMP) Sensor Bolt(s)	7.4 ft-lbs
Oxygen (O2S) Sensor Bolt(s)	30.0 ft-lbs
Knock Sense (KS) Bolt(s)	18.0 ft-lbs
Oil Pan to Block Bolts	9.0 ft-lbs
Engine Oil Pan Drain Plug	18.0 ft-lbs
Oil Pump to Cylinder BLock Bolts/Studs	6 MM
Engine Valve Cover Bolts	7.4 ft-lbs

Chassis torques

Lug Nuts

92 ft-lbs

Ignition

Cylinder Firing Order

1-5-4-2-6-3-7-8

Service checks

Regulated Fuel System Pressure (Without Vacuum)	65.0 Low pressure side. psi
Regulated Fuel System Pressure (With Vacuum)	65.0 Low pressure side. psi
Fuel Pump Pressure Minimum	65.0 Low Pressure Side psi
RPM	65.0 @ start up rpm
RPM	65.0 @ start up. Low pressure side. rpm
Engine Compression	Cranking speed

Multi-step torque procedures OEM · verified

Connecting Rod (Large End) Bearings — tightening sequence 2 stages

1	84.0 inch lbs.	84 in
2	37.0

Crankshaft Pulley and/or Damper Bolts — tightening sequence 1 stages

1

148.0 ft. lbs., Step 2: 270

148 ft. lbs

Cylinder Head — tightening sequence 6 stages

Prep with the following procedure.

1	Bolts 1-10	15 ft. lbs
2	Bolts 1-10	25.8 ft. lbs
3	Bolts 1-10	90 degrees
4	Bolts 1-10	120 degrees
5	18.0
6	Bolts 12-13	9 ft. lbs

Cylinder Head — tightening sequence 6 stages

1	Bolts 1-10	15 ft. lbs
2	Bolts 1-10	26 ft. lbs
3	Bolts	90 degrees
4	Bolts 1-10	120 degrees
5	Bolt 11	18 ft. lbs
6	9

Engine Flywheel Bolts — tightening sequence 2 stages

1	33.0 ft. lbs.	33 ft. lbs
2	90.0

Main Bearings — tightening sequence 3 stages

Prep M10 Bolts

1	18.0 ft. lbs.	18 ft. lbs
2	42.0 ft. lbs.	42 ft. lbs
3	70.0 degrees; M8 Bolts	70 degrees
1	11.0 ft. lbs.	11 ft. lbs
2	24.0 ft. lbs.	24 ft. lbs
3	75.0

Factory maintenance schedule OEM · verified

Normal service, condensed from the factory interval matrix.

Under the factory schedule, replace the engine oil and filter every 16,000 mi; spark plugs every 96,000 mi; coolant at 160,000 mi. The big-interval services (at 160,000 mi for coolant, and the transmission fluid) are the ones owners most often skip — on a lower-mileage example, assume the original fluids are still in it and check them first.

Every 16,000 mi	Brake System (inspect) · Engine Assembly (leak inspection) · Engine Oil (drain & refill) · Engine Oil Filter (replace) · Engine Oil Level Warning System (inspect) · Sunroof Assembly (lubricate)
Every 32,000 mi	Cabin Air Filter (replace) · Temperature Controlled Seat Air Filter (replace)
Every 48,000 mi	Brake Hydraulic System (drain, refill & bleed) · Engine Air Filter Element (replace)
Every 96,000 mi	Spark Plugs (replace)
At 144,000 mi	Drive Belt (replace) · Transmission Assembly (drain & refill)
At 160,000 mi	Engine Coolant System (drain, flush & refill)