Fluid capacities, tune-up values and fuel economy at a glance.
Engine oil capacity4.5 qtOEM · verified
Engine oil type5W-30OEM · verified
Lug nut torque140 ft-lbsOEM · verified
Fitment & sizes
Replacement part sizes and factory part numbers — battery, bulbs, filters and belts.
From the factory this vehicle uses a BCI 78 · 600 CCA battery, OE oil filter 12690386. Each part links to every other vehicle that shares it, so a part you already stock may fit more of your fleet than you'd expect.
Capacities, torques and tune-up values from the factory service manual.
This engine holds 4.5 qt of 5W-30 engine oil, SAE 75W · SYNTHETIC in the differential, DOT 3 brake fluid. Torque lug nuts to 140 ft-lbs, the oil drain plug to 18.0 ft-lbs. The firing order is 1-8-7-2-6-5-4-3. Note the cylinder-head bolts finish on a torque angle (torque-to-yield) — they stretch permanently and should be replaced, not reused, during any head service.
74 ft. lbs., step 2: 100 degrees., step 3: 90 degrees., install new bolt.
74 ft. lbs
Cylinder Head — tightening sequence 3 stages
Prep Do not reuse old bolts. Do not allow oil on cylinder head or head bolt bosses · M11 Bolts:
1
22.0 ft. lbs.
22 ft. lbs
2
90 degrees
90 degrees
3
70 degrees; M8 Bolts:
70 degrees
1
22.0 ft. lbs.
22 ft. lbs
Cylinder Head — tightening sequence 3 stages
Prep Do not reuse old bolts. Do not allow oil on cylinder head or head bolt bosses · M11 Bolts 1-10:
1
22.0 ft. lbs.
22 ft. lbs
2
90 degrees
90 degrees
3
70 degrees; M8 Bolts 11-15:
70 degrees
1
22.0 ft. lbs.
22 ft. lbs
Cylinder Head — tightening sequence 3 stages
Prep Do not reuse old bolts. Do not allow oil on cylinder head or head bolt bosses · M11 Bolts 1-10:
1
22.0 ft. lbs.
22 ft. lbs
2
90 degrees
90 degrees
3
70 degrees; M8 Bolts 11-15:
70 degrees
1
22.0 ft. lbs.
22 ft. lbs
Cylinder Head — tightening sequence 1 stages
1
all bolts
22 ft. lbs
Intake Manifold to Engine Bolts — tightening sequence 1 stages
1
3.7 ft. lbs., step 2: 7.4
3.7 ft. lbs
Exhaust Manifold to Cylinder Head Bolts — tightening sequence 1 stages
1
11 ft. lbs., step 2: 15
11 ft. lbs
Intake Manifold to Engine Bolts — tightening sequence 1 stages
1
3.7 ft. lbs., step 2: 7.4
3.7 ft. lbs
Exhaust Manifold to Cylinder Head Bolts — tightening sequence 1 stages
1
11 ft. lbs., step 2: 15
11 ft. lbs
Intake Manifold to Engine Bolts — tightening sequence 1 stages
1
3.7 ft. lbs., Step 2: 7.4
3.7 ft. lbs
Exhaust Manifold to Cylinder Head Bolts — tightening sequence 1 stages
1
11 ft. lbs., Step 2: 15
11 ft. lbs
Intake Manifold to Engine Bolts — tightening sequence 1 stages
1
3.7 ft. lbs., Step 2: 7.4
3.7 ft. lbs
Exhaust Manifold to Cylinder Head Bolts — tightening sequence 1 stages
1
11 ft. lbs., Step 2: 18
11 ft. lbs
Factory maintenance schedule OEM · verified
Normal service, condensed from the factory interval matrix.
Under the factory schedule, replace the engine oil and filter every 7,500 mi; spark plugs every 97,500 mi; coolant at 150,000 mi. The big-interval services (at 150,000 mi for coolant, and the transmission fluid) are the ones owners most often skip — on a lower-mileage example, assume the original fluids are still in it and check them first.
Every 7,500 mi
Accelerator Pedal (inspect) · Body Latches, Locks & Hinges (lubricate) · Brake Shift Interlock Solenoid (inspect) · Brake System (inspect) · Engine Air Filter Element (inspect) · Engine Oil (inspect fluid level)