GMC TruckC-Series Topkick Commercial C4/C52004Overview/gmc-truck/c-series-topkick-commercial-c4-c5/2004/base/

2004 GMC Truck C-Series Topkick Commercial C4/C5

Factory specifications, fluid capacities, torque values, EPA fuel economy and the federal safety record for the 2004 C-Series Topkick Commercial C4/C5.

Service quick specs OEM factory data

Capacities, torques and tune-up values from the factory service manual.

Torque the oil drain plug to 21.0 ft-lbs. Note the cylinder-head bolts finish on a torque angle (torque-to-yield) — they stretch permanently and should be replaced, not reused, during any head service.

Engine torques

Crankshaft Pulley and/or Damper Bolts189 ft-lbs
Intake Manifold to Engine Bolts15 ft-lbs
Exhaust Manifold to Cylinder Head Bolts28 ft-lbs
Intake Manifold to Engine BoltsRight: 15 ft-lbs
Exhaust Manifold to Cylinder Head Bolts28 ft-lbs
Exhaust Manifold to Cylinder Head BoltsBolts: 26 ft-lbs, nuts: 12 ft-lbs
Engine Oil Pan Drain Plug62.0 ft-lbs
Engine Oil Pan Drain Plug21.0 ft-lbs

Battery & A/C

RefrigerantR134a
Refrigerant Capacity2.13 lbs
Oil GroupPAG
Oil Type46
Oil Capacity8.00 oz

Service checks

Injector Primary Resistance11-14 @ 50-90 degreesF ohms
Engine Compression100 Minimum psi
Engine Compression215 Nominal psi
Engine Compression100 Minimum psi
Engine Compression100 Minimum psi

Multi-step torque procedures OEM · verified

Crankshaft Pulley and/or Damper Bolts — tightening sequence 1 stages
174 ft. lbs., step 2: 9074 ft. lbs
Cylinder Head — tightening sequence 4 stages

Prep M12 bolts:

137 ft. lbs.37 ft. lbs
259 ft. lbs.59 ft. lbs
360 degrees60 degrees
490 degrees; M8 bolts:90 degrees
118
Cylinder Head — tightening sequence 3 stages

Prep M12 bolts:

137 ft. lbs.37 ft. lbs
259 ft. lbs.59 ft. lbs
390 degrees; M8 bolts:90 degrees
118
Cylinder Head — tightening sequence 6 stages
122 ft. lbs.22 ft. lbs
222 ft. lbs.22 ft. lbs
3120 degrees120 degrees
4bolts 1, 2, 3, 6, 7, 8, 9, 10, 11, 14, 16, 1760 degrees
5bolts 15, 1845 degrees
6turn 30
Intake Manifold to Engine Bolts — tightening sequence 1 stages
13.7 ft. lbs., step 2: 5.9 ft. lbs., step 3: 8.83.7 ft. lbs

Common OBD-II trouble codes

The most common OBD-II codes for this vehicle's emissions system. These are standardized SAE J2012 definitions, not vehicle-specific fault reports.

P0420
Catalyst system efficiency below threshold — Bank 1
P0300
Random / multiple cylinder misfire detected
P0171
System too lean — Bank 1
P0455
Evaporative emission system leak detected — large leak
P0128
Coolant thermostat below regulating temperature
P0442
Evaporative emission system leak detected — small leak

VIN tools

Decode factory build data for a specific vehicle by VIN.

VIN
Decode a VIN to confirm the transmission and build data for a specific C-Series Topkick Commercial C4/C5. OEM
Build data
Plant, GVWR class, engine and body data for any 17-character VIN.
Recalls
Check open recall campaigns against a specific vehicle by VIN.

Reference guides

Cross-vehicle references for the kinds of data on this page.