FordExplorer2014Overview/ford/explorer/2014/base/

2014 Ford Explorer

Factory specifications, fluid capacities, torque values, EPA fuel economy and the federal safety record for the 2014 Explorer.

Body SUVTransmission Automatic (S6)

The 2014 Ford Explorer is an SUV that uses a 5.7‑quart oil capacity with 5W‑30 API viscosity and comes equipped with an automatic six‑speed transmission, delivering EPA fuel economy of 17/23/19 mpg. In its first full year of ownership it generated 1,671 total owner complaints, with steering problems accounting for the largest share and seven recall campaigns issued. Historically the model’s complaint volume peaks at 3,620 in 2002 and falls to 12 in 1990, placing the 2014 model in the middle of that historical range and indicating a moderate level of reliability concern.

Model year202620252024202320212020201920182014

Quick specs

Fluid capacities, tune-up values and fuel economy at a glance.

Engine oil capacity5.7 qtOEM · verified
Engine oil type5W-30 APIOEM · verified
Lug nut torque100 ft-lbsOEM · verified
EPA fuel economy17/23/19 mpgEPA · verified

Fitment & sizes

Replacement part sizes and factory part numbers — battery, bulbs, filters and belts.

From the factory this vehicle uses a BCI 65 w/Power Code Remote Start · 650 w/Power Code Remote Start CCA battery. Each part links to every other vehicle that shares it, so a part you already stock may fit more of your fleet than you'd expect.

Battery groupBCI 65 w/Power Code Remote Start · 650 w/Power Code Remote Start CCAOEM · verified
Tire sizeP245-60R18OEM · verified

Full specifications

Engine, drivetrain, dimensions and economy.

Engine & drivetrain NHTSA vPIC

TransmissionAutomatic (S6)

Dimensions & weight NHTSA vPIC

Overall length197.2 in
Overall width78.7 in
Overall height70.5 in
Wheelbase112.6 in
Curb weight4731 lb
Track (front / rear)66.9 / 66.9 in
Weight distribution (front / rear)54/46

Ratings & economy EPA / vPIC

EPA city / highway / combined17 / 23 / 19 mpg
DrivetrainAll-Wheel Drive
Recommended fuelRegular Gasoline

Performance & power Independent road tests

0–60 mph, quarter-mile, horsepower and torque from independent road tests.

Independent road tests for the Explorer of this era, listed by trim and engine — this page spans more than one engine, so no single horsepower figure is shown.

5.8–9.2 sec0–60 mph (tested)quickest 5.80 sec — 2017 Platinum EcoBoost
YearTrim / engine0–60¼ mileHPDrivetrain
2013Sport EcoBoost 3.5L Twin-Turbo V65.90 sec14.50 sec365 hpAWD
2013Limited 3.5L V68.00 sec16.10 sec290 hpAWD
2012Limited 2.0L EcoBoost 2.0L Turbo I-49.20 sec16.90 sec240 hpFWD
2016Sport EcoBoost 3.5L Twin-Turbo V66.00 sec14.60 sec365 hpAWD
2016Platinum EcoBoost 3.5L Twin-Turbo V66.40 sec14.80 sec365 hpAWD
2016Limited 2.3L EcoBoost 2.3L Turbo I-48.20 sec16.30 sec280 hpAWD
2011Limited 3.5L V67.50 sec16.00 sec290 hpAWD
2011XLT 3.5L V67.70 sec16.00 sec290 hpAWD

Service quick specs OEM factory data

Capacities, torques and tune-up values from the factory service manual.

This engine holds 5.7 qt of 5W-30 API engine oil, 80W-90 · GL-5 in the differential, DOT 3 brake fluid. Torque lug nuts to 100 ft-lbs, the oil drain plug to 18.0 ft-lbs. The firing order is 1-4-2-5-3-6. Note the cylinder-head bolts finish on a torque angle (torque-to-yield) — they stretch permanently and should be replaced, not reused, during any head service.

Lubricants & capacities

Automatic Transmission FluidFord Mercon LV
Automatic Transmission Fluid Capacity10.0-12.0
Brake FluidDOT 3
Differential Gear Oil80W-90 · GL-5
Differential Gear Oil Capacity2.4 Pints
Engine Oil5W-30 · API
Engine Oil Capacity5.7 qt
Engine Oil5W-20 · API

Engine torques

Engine Flywheel Bolts59 ft-lbs
Intake Manifold to Engine BoltsLower: 7.4 ft-lbs
Exhaust Manifold to Cylinder Head Bolts29.5 ft-lbs
Intake Manifold to Engine Bolts14.7 ft-lbs
Exhaust Manifold to Cylinder Head BoltsInstall new studs: 12.5 ft-lbs, Step 2:
Engine Oil Pan Drain Plug18.0 ft-lbs
Engine Oil Pan Drain Plug18.0 ft-lbs
Engine Oil Pan Drain Plug18.0 ft-lbs

Chassis torques

Lug Nuts100 ft-lbs
Transfer Case Fill Plug15.0 ft-lbs
Transfer Case Drain Plug9.0 if equipped with drain plug ft-lbs
Front Wheel Hub285 ft-lbs
Rear Wheel Hub285 ft-lbs

Ignition

Cylinder Firing Order1-3-4-2
Cylinder Firing Order1-4-2-5-3-6
Spark Plug ManufacturerMotorcraft
Spark Plug Gap0.049-0.053 in
Spark Plug Torque9.0 ft-lbs

Battery & A/C

RefrigerantR134a
Oil GroupPAG
Oil Type46
Standard BCI Group Number65 w/Power Code Remote Start
Standard BCI Cranking Performance650 w/Power Code Remote Start cca
Optional BCI Group Number65
Optional BCI Cranking Performance650 cca

Service checks

Pressure Test18-20 psi
Thermostat Opening Temperature180-207 °F
Pressure Test18 psi
Radiator Cap Pressure Relief13-18 psi
Thermostat Opening Temperature176-183 °F
Pressure Test18 psi
Radiator Cap Pressure Relief13-18 psi
Thermostat Opening Temperature175-182 °F

Brakes

Minimum Pad ThicknessFront: 0.118; Rear: 0.118 in
Rotor Runout Limit0.002 in
Rotor Discard at or Under1.122 in / 0.394 in

Multi-step torque procedures OEM · verified

Camshaft Bearing/Carrier Cap Bolts or Studs — tightening sequence 1 stages
1Tighten all bolts to finger tight. Step 25 ft. lbs
Camshaft Bearing/Carrier Cap Bolts or Studs — tightening sequence 1 stages
16 ft. lbs., Step 2: 456 ft. lbs
Connecting Rod (Large End) Bearings — tightening sequence 1 stages
122 ft. lbs., Step 2: 9022 ft. lbs
Connecting Rod (Large End) Bearings — tightening sequence 1 stages
117 ft. lbs. Step 2: 32 ft. lbs., Step 3: 9017 ft. lbs
Crankshaft Pulley and/or Damper Bolts — tightening sequence 1 stages
189 ft. lbs., step 2: 360 degrees, step 3: 37 ft. lbs., step 4: 9089 ft. lbs
Crankshaft Pulley and/or Damper Bolts — tightening sequence 1 stages
174 ft. lbs., step 2: 100 ft. lbs., step 3: 90 degrees.74 ft. lbs
Cylinder Head — tightening sequence 5 stages

Prep Do not reuse old bolts. Use new bolts coated with clean engine oil. Tighten all bolts to finger tight then continue on with the following procedure.

15.17 ft. lbs.5.17 ft. lbs
211.0 ft. lbs.11 ft. lbs
341.0 ft. lbs.41 ft. lbs
490 degrees90 degrees
590 degrees90 degrees
Cylinder Head — tightening sequence 5 stages

Prep Do not reuse old bolts. Coat new bolts with the specified engine oil. · Bolts 1-8

115.0 ft. lbs.15 ft. lbs
226.0 ft. lbs.26 ft. lbs
390 degrees90 degrees
490 degrees90 degrees
545 degrees; Bolt 945 degrees
17.4 ft. lbs.7.4 ft. lbs
Cylinder Head — tightening sequence 7 stages

Prep Do not reuse old bolts. Coat new bolts with the specified engine oil. · Bolts 1-18

115.0 ft. lbs.15 ft. lbs
236.0 ft. lbs.36 ft. lbs
336.0 ft. lbs.36 ft. lbs
436.0 ft. lbs.36 ft. lbs
590 degrees90 degrees
690 degrees90 degrees
790 degrees; Bolts 19-2290 degrees
122 ft. lbs.22 ft. lbs
Cylinder Head — tightening sequence 5 stages

Prep Do not reuse old bolts. Coat new bolts with the specified engine oil. · Bolts 1-8

115.0 ft. lbs.15 ft. lbs
226.0 ft. lbs.26 ft. lbs
390 degrees90 degrees
490 degrees90 degrees
545 degrees; Bolt 945 degrees
17.4 ft. lbs.7.4 ft. lbs
Engine Flywheel Bolts — tightening sequence 1 stages
137 ft. lbs., Step 2: 59 ft. lbs., Step 3: 83 ft. lbs., Step 4: 9037 ft. lbs
Main Bearings — tightening sequence 1 stages
14 ft. lbs., Step 2: 18 ft. lbs., Step 3: 604 ft. lbs
Oil Pump to Cylinder BLock Bolts/Studs — tightening sequence 1 stages
17 ft. lbs., Step 2: 157 ft. lbs

Factory maintenance schedule OEM · verified

Normal service, condensed from the factory interval matrix.

Under the factory schedule, replace the spark plugs every 100,000 mi; coolant every 50,000 mi. The big-interval services (every 50,000 mi for coolant, and the transmission fluid) are the ones owners most often skip — on a lower-mileage example, assume the original fluids are still in it and check them first.

Every 10,000 miAir Conditioning Condenser (inspect) · Air Conditioning Refrigerant Line (inspect) · Battery (inspect) · Brake Line (inspect) · Brake System (inspect) · CV Joint Boot (inspect)
Every 20,000 miAccessory Drive Belt (inspect) · Cabin Air Filter (replace)
Every 30,000 miEngine Air Filter Element (replace) · Temperature Controlled Seat Air Filter (replace)
Every 50,000 miEngine Coolant System (drain, flush & refill)
At 100,000 miAccessory Drive Belt (inspect) · Engine Coolant System (drain, flush & refill)
Every 100,000 miSpark Plugs (replace)
At 150,000 miDrive Belt (replace) · Transmission Assembly (drain & refill)

Reliability & federal safety record

Owner-reported issues, recalls, investigations and service bulletins on record with NHTSA — an unfiltered look at what owners actually experience.

The 2014 Explorer sits in a period of moderate complaint activity, with 1,671 complaints and 7 recalls—slightly below the 2,223 complaints recorded in 2013 and the 2,428 complaints in 2016, but higher than the 710 complaints in 2018. The recall count of seven is comparable to the 12 recalls in 2013 and the 15 recalls in 2017, indicating a steady but not exceptional safety concern trend. The most frequent complaint areas for 2014—Steering (415), Unknown Or Other (250), Structure (235), and Engine (114)—mirror the broader pattern of component‑specific issues that persisted across the generation. Crash complaints were relatively low at 32, and fire complaints at six, suggesting no spike in those critical categories. Overall, 2014 falls near the middle of the trend curve, implying that while the Explorer had typical issues for its generation, it is not an outlier; therefore, a 2014 model can be a reasonable purchase if inspected for steering and structural components.

7
Open recalls
NHTSA campaigns
130
Service bulletins
Manufacturer communications
4
ODI investigations
Office of Defects Investigation
1,671
Owner complaints
32 involved a crash · 6 a fire
NHTSA crash-test rating federal NCAP · out of 5 stars
Overall★★★★★
Frontal★★★★★
Side★★★★★
Rollover★★★★

Owner complaints filed with NHTSA, by component

All 1,671 complaints on record, top 8 components.

Steering415
Unknown Or Other250
Structure235
Engine114
Suspension68
Power Train49
Engine & Engine Cooling46
Electrical System31

Source: NHTSA Office of Defects Investigation complaint database.

Recalls NHTSA · verified

Showing 2 of 7 campaigns on record for this vehicle.

19V435000Suspension:RearReported 10/06/2019

Ford Motor Company (Ford) is recalling certain 2011-2017 Explorer vehicles. The rear suspension toe links may fracture due to stress on the rear suspension. Remedy: Ford will notify owners, and dealers will replace the rear suspension toe links, and inspect both rear toe link ball joints, replacing the rear wheel knuckle(s), if necessary…

17E048000Wheels:HubReported 28/08/2017

Ford Motor Company (Ford) is recalling certain Wheel Hub Bearing assemblies, part number HB5Z-1104-C, incorrectly listed as being for installation on the rear axles of 2011-2017 Ford Explorer 4X2 vehicles. These… Remedy: Ford will notify the distributors of the hubs specifying that they are to only be used on drive axles. It is believed that none of the hubs were purchased from Ford dealers for…

Technical service bulletins NHTSA · verified

Showing 5 of 130 bulletins on record with NHTSA.

BulletinDateComponentSummary
SSM 546012026-02-23Electrical SystemFord and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory…
SSM 530402024-10-10Unknown Or OtherWhile performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a…
SSM 524762024-04-24EquipmentAll accessory stick-on keyless entry keypads come with a wallet card containing the…
SSM 515362023-04-04StructureFor 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis…
22N01 S12023-02-07SuspensionCertain 2011-2017 Model Year Explorer Vehicles Rear Wheel Knuckle Replacement REASON FOR…

Common OBD-II trouble codes

The most common OBD-II codes for this vehicle's emissions system. These are standardized SAE J2012 definitions, not vehicle-specific fault reports.

P0420
Catalyst system efficiency below threshold — Bank 1
P0300
Random / multiple cylinder misfire detected
P0171
System too lean — Bank 1
P0455
Evaporative emission system leak detected — large leak
P0128
Coolant thermostat below regulating temperature
P0442
Evaporative emission system leak detected — small leak

VIN tools

Decode factory build data for a specific vehicle by VIN.

VIN
Decode a VIN to confirm the transmission and build data for a specific Explorer. OEM
Build data
Plant, GVWR class, engine and body data for any 17-character VIN.
Recalls
Check open recall campaigns against a specific vehicle by VIN.

Vehicles with shared specs

Find every vehicle that shares this one's battery, bulbs, oil capacity, platform or parts.

Reference guides

Cross-vehicle references for the kinds of data on this page.

Frequently asked

How much oil does the 2014 Explorer take?

5.7 qt of 5W-30 API MEETING FORD SPECIFICATION WSS-M2C946-A, per the factory manual.

Does the 2014 Explorer have open recalls?

NHTSA lists 7 recall campaign(s) for this model year. Check your specific vehicle by VIN.

What gas mileage does the Explorer get?

EPA figures are 17 city / 23 highway / 19 combined mpg.