Factory specifications, fluid capacities, torque values, EPA fuel economy and the federal safety record for the 2010 760Li Sedan.
The 2010 BMW 760Li Sedan. It takes 11.0 qt of 15W-40 engine oil and is EPA-rated at 13/19/15 mpg city/highway/combined.
Fluid capacities, tune-up values and fuel economy at a glance.
Replacement part sizes and factory part numbers — battery, bulbs, filters and belts.
From the factory this vehicle uses a BCI 49 · 900 CCA battery, OE oil filter 11427583220. Each part links to every other vehicle that shares it, so a part you already stock may fit more of your fleet than you'd expect.
| Engine oil filter | 11427583220 |
| Engine air filter | 13717593250 |
| Spark plug | 12120037580 |
| Battery | 61217594976 |
| Front wiper blades | 61612147361 |
| Thermostat | 11538632664 alt 11537586885 |
| Cabin air filter | 64319175484 alt 64119272642 |
Engine, drivetrain, dimensions and economy.
| Transmission | Automatic (S8) |
| EPA city / highway / combined | 13 / 19 / 15 mpg |
| Drivetrain | Rear-Wheel Drive |
| Passenger volume | 115 cu ft |
| Cargo volume | 14 cu ft |
| Recommended fuel | Premium Gasoline |
Capacities, torques and tune-up values from the factory service manual.
This engine holds 11.0 qt of 15W-40 / 10W-40 / 10W-30 API SJ engine oil, DOT 4 brake fluid. Torque lug nuts to 103 ft-lbs, the oil drain plug to M12 Bolts: 18.0, M22 Bolts: 44.0 ft-lbs. The firing order is 1-7-5-11-3-9-6-12-2-8-4-10. Note the cylinder-head bolts finish on a torque angle (torque-to-yield) — they stretch permanently and should be replaced, not reused, during any head service.
| Automatic Transmission Fluid | BMW part number 83222152426 |
| Automatic Transmission Fluid Capacity | 10.5-11.5 |
| Brake Fluid | DOT 4 |
| Differential Gear Oil Capacity | 1.8 Pints |
| Engine Coolant | ETHYLENE GLYCOL |
| Engine Oil | 15W-40 · API · 10W-40 · 10W-30 · 5W-30 |
| Engine Oil Capacity | 11.0 qt |
| Power Steering Fluid | Use Pentosin CHF 11S |
| Engine Oil Pan Drain Plug | M12 Bolts: 18.0, M22 Bolts: 44.0 ft-lbs |
| Lug Nuts | 103 ft-lbs |
| Front Wheel Hub | 310 ft-lbs |
| Cylinder Firing Order | 1-7-5-11-3-9-6-12-2-8-4-10 |
| Spark Plug Manufacturer | BMW |
| Refrigerant | R134a |
| Oil Group | PAG |
| Standard BCI Group Number | 49 |
| Standard BCI Cranking Performance | 900 cca |
| Optional BCI Group Number | 49 |
| Optional BCI Cranking Performance | 850 cca |
| Pressure Test | 21.7 psi |
| Radiator Cap Pressure Relief | 24-32 psi |
| Engine Compression | 203-261 PSI. 29 maximum variance. psi |
| Brake Application | WITH FN3 |
| Torque to Knuckle | 81 ft-lbs |
| Minimum Pad Thickness | Front: 0.145; Rear: 0.145 pads |
| Brake Application | WITH FN3 |
| Rotor Nominal Thickness From | 1.181 in / 0.787 in / 0.945 in / 1.417 in |
| Rotor Nominal Thickness To | 1.181 in / 0.787 in / 0.945 in / 1.417 in |
| Rotor Minimum Machining | 0.031 in |
| Rotor Discard at or Under | 1.087 in / 0.692 in / 0.882 in / 1.354 in |
Prep Do not reuse old bolts
| 1 | 22.0 ft. lbs. | 22 ft. lbs |
| 2 | 90 degrees | 90 degrees |
| 3 | 140 degrees | 140 degrees |
Normal service, condensed from the factory interval matrix.
Under the factory schedule, replace the spark plugs every 60,000 mi.
| Every 60,000 mi | Spark Plugs (replace) |
| Every 100,000 mi | Transmission Assembly (drain & refill) |
| At 120,000 mi | Oxygen Sensor (replace) |
The most common OBD-II codes for this vehicle's emissions system. These are standardized SAE J2012 definitions, not vehicle-specific fault reports.
Decode factory build data for a specific vehicle by VIN.
Find every vehicle that shares this one's battery, bulbs, oil capacity, platform or parts.
Cross-vehicle references for the kinds of data on this page.
11.0 qt of HIGH PERFORMANCE MINERAL OILS: ABOVE 5 degrees F: 15W-40 API SJ, SL OR SM, -5 degreesF TO 68 degrees F: 10W-40 API SJ, SL OR SM, 5 degreesF TO 50 degrees F: 10W-30 API SJ, SL OR SM, BELOW 50 degrees F: 5W-30 API SJ, SL OR SM, BELOW 32 degrees F:, per the factory manual.
EPA figures are 13 city / 19 highway / 15 combined mpg.