Factory specifications, fluid capacities, torque values, EPA fuel economy and the federal safety record for the 2010 528i Sedan.
The 2010 BMW 528i Sedan. It takes 6.9 qt of 15W-40 engine oil and is EPA-rated at 18/27/21 mpg city/highway/combined.
Fluid capacities, tune-up values and fuel economy at a glance.
Replacement part sizes and factory part numbers — battery, bulbs, filters and belts.
From the factory this vehicle uses a BCI 49 · 850 CCA battery, OE oil filter 11428683168. Each part links to every other vehicle that shares it, so a part you already stock may fit more of your fleet than you'd expect.
| Engine oil filter | 11428683168 alt 11428637821 |
| Engine air filter | 13717521033 |
| Fuel filter | 16117373514 |
| Spark plug | 12120037663 alt 12122158253 |
| Battery | 61217586962 alt 61217586961 |
| Front wiper blades | 61612455442 |
| Thermostat | 11537549476 |
| Cabin air filter | 64319171858 |
Engine, drivetrain, dimensions and economy.
| Transmission | Automatic (S6) |
| Overall length | 190.9 in |
| Overall width | 72.8 in |
| Overall height | 57.9 in |
| Wheelbase | 114.2 in |
| Curb weight | 3505 lb |
| Track (front / rear) | 61 / 61.8 in |
| Weight distribution (front / rear) | 51/49 |
| EPA city / highway / combined | 18 / 27 / 21 mpg |
| Drivetrain | Rear-Wheel Drive |
| Passenger volume | 99 cu ft |
| Cargo volume | 14 cu ft |
| Recommended fuel | Premium Gasoline |
Capacities, torques and tune-up values from the factory service manual.
This engine holds 6.9 qt of 15W-40 / 10W-40 / 10W-30 API SJ engine oil, DOT 4 brake fluid. Torque lug nuts to 88 ft-lbs, the oil drain plug to M12 Bolts: 18.0, M22 Bolts: 44.0 ft-lbs. The firing order is 1-5-3-6-2-4. Note the cylinder-head bolts finish on a torque angle (torque-to-yield) — they stretch permanently and should be replaced, not reused, during any head service.
| Automatic Transmission Fluid | BMW part number 83222152426 |
| Automatic Transmission Fluid Capacity | 10.5-11.5 |
| Brake Fluid | DOT 4 |
| Differential Gear Oil Capacity | 1.8 Pints |
| Engine Coolant | ETHYLENE GLYCOL |
| Engine Oil | 15W-40 · API · 10W-40 · 10W-30 · 5W-30 |
| Engine Oil Capacity | 6.9 qt |
| Manual Transmission Fluid | BMW MTF part number 83220309031 |
| Crankshaft Pulley and/or Damper Bolts | 18 ft-lbs |
| Intake Manifold to Engine Bolts | 11 ft-lbs |
| Exhaust Manifold to Cylinder Head Bolts | 15 ft-lbs |
| Engine Oil Pan Drain Plug | M12 Bolts: 18.0, M22 Bolts: 44.0 ft-lbs |
| Lug Nuts | 88 ft-lbs |
| Rear Wheel Hub | 310 ft-lbs |
| Cylinder Firing Order | 1-5-3-6-2-4 |
| Spark Plug Manufacturer | BMW |
| Refrigerant | R134a |
| Refrigerant Capacity | 1.76-1.90 lbs |
| Oil Group | PAG |
| Oil Type | 46 |
| Oil Capacity | 5.40-6.80 oz |
| Standard BCI Group Number | 49 |
| Standard BCI Cranking Performance | 850 cca |
| Optional BCI Group Number | 95R |
| Pressure Test | 21.7 psi |
| Radiator Cap Pressure Relief | 28-32 psi |
| Brake Application | WITH FN3 |
| Torque Caliper to Bracket | 22-26 ft-lbs |
| Torque to Knuckle | 81 ft-lbs / 48 ft-lbs |
| Minimum Pad Thickness | Front: 0.145; Rear: 0.145 pads |
| Brake Application | WITH FN3 |
| Rotor Nominal Thickness From | 1.181 in / 1.417 in / 0.945 in / 0.787 in |
| Rotor Nominal Thickness To | 1.181 in / 1.417 in / 0.945 in / 0.787 in |
| Rotor Minimum Machining | 0.031 in |
Prep Do not reuse old bolts
| 1 | 22.0 ft. lbs. | 22 ft. lbs |
| 2 | 90 degrees | 90 degrees |
| 3 | Bolts 1-10 90 degrees | 90 degrees |
| 4 | 45 degrees | 45 degrees |
Normal service, condensed from the factory interval matrix.
Under the factory schedule, replace the spark plugs every 60,000 mi.
| Every 60,000 mi | Spark Plugs (replace) |
| Every 100,000 mi | Transmission Assembly (drain & refill) |
| At 120,000 mi | Oxygen Sensor (replace) |
The most common OBD-II codes for this vehicle's emissions system. These are standardized SAE J2012 definitions, not vehicle-specific fault reports.
Decode factory build data for a specific vehicle by VIN.
Find every vehicle that shares this one's battery, bulbs, oil capacity, platform or parts.
Cross-vehicle references for the kinds of data on this page.
6.9 qt of HIGH PERFORMANCE MINERAL OILS: ABOVE 5 degrees F: 15W-40 API SJ, SL OR SM, -5 degreesF TO 68 degrees F: 10W-40 API SJ, SL OR SM, 5 degreesF TO 50 degrees F: 10W-30 API SJ, SL OR SM, BELOW 50 degrees F: 5W-30 API SJ, SL OR SM, BELOW 32 degrees F:, per the factory manual.
EPA figures are 18 city / 27 highway / 21 combined mpg.